Buttons and Connectors
Quad USB Ports
- Qualcomm Quick Charge 3.0 Technology means you can charge your device up to 400% faster than conventional (compatible with Quick Charge 1.0 & 2.0 devices as well)
- ZEN+ Technology means each port automatically detects your device and fine tunes the output to charge it at maximum speed (up to 3.1A each port, and 3.1A in total).
- Charge other devices while Zendure A-Series is being charged
- Turns itself on automatically when connected to compatible devices
- Maintains up to 95% of charge after six months in standby (when USB disconnected)
- Quad USB output for charging four devices at the same time
Apple: iPhone 7, 6s, 6S Plus, 6, 6 plus 5S, 5C, 5 / iPod / iPad, iPad mini, etc
HTC: One X, S, V / Sensation Series / EVO 4G / Radar 4G / Inspire 4G / Vivid 4G / Wildfire S / Desire series, etc.
Samsung: Galaxy S Series / Galaxy Note Series / Galaxy Nexus / Focus S / Infuse, etc.
Motorola: Droid Razr, Bionic / Atrix / Triumph, etc. LG: Nexus, Optimus Series, etc.
Nokia: Lumia Series / N8 / N9, etc.
Others: Blackberry / Sony Ericsson / PSP / Nook / MP3 MP4 MP5 / GoPro / Amazon Kindle series, etc.
Compatible with most 5V input USB powered devices that can draw over 120mA of current.
Capacity: 26,800 mAh, 3.7V / 99.2Wh
Battery Cell: Premium high-density Lithium-ion
Dimensions: 4.7” x 2.8” x 1.6” (119 mm x 73 mm x 40 mm) Weight: 17.0 oz / 483 g
Input: Micro USB 5V/2.0A, 9V/2.0A, 12V/1.5A (18W)
Input Charging Time: ~10 hours (QC3.0); ~14 hours (5V/2.0A)
Output: USB1—5-6V/3.0A,6-9V/2.0A,9-12V/1.5A (18W), USB2/3/4—5V/3.1A (15.5W) MAX with ZEN+
Product Life: Over 500 full charge-discharge cycles
Operating Temperature: 32°F to 113°F / 0°C to 45°C (Charging); -4°F to 149°F / -20°C to 65°C (Discharging)
Charging your Zendure A8 QC
Connect one end of the charging cable to a powered USB port. We recommend using a Quick Charge 3.0 certified charger, which gives you the fastest charging experience and takes only 10 hours to complete the charge. It will take other power sources such as a 5V/2A (10W) charger about 14 hours.
Connect the other end of the cable to the Micro USB input port on your Zendure. If the power source is active, your Zendure should begin charging immediately. Your Zendure may remain connected to the power source indefinitely; there is no risk of overcharging it.
Charge status will be displayed by the digital charge indicator on your Zendure. Please refer to the illustration below
Using your Zendure A8 QC to charge other devices
Connect one end of the included USB cable or other USB cable to the USB output port on your Zendure. Connect the other end of the USB charging cable to the charging port on your compatible device, using an appropriate adaptor if necessary.
Your Zendure will automatically begin charging most devices when connected if the current drawn is over 120mA. If charging doesn’t start on its own, press the power button briefly to begin charging.
While your Zendure is charging your device, the charge indicator on your Zendure will display the remaining charge. Please refer to the table below.
Checking your Zendure’s remaining charge
If your Zendure’s charge indicator is not already lit, press the power button briefly. If the lights still do not turn on, your Zendure has no charge remaining. The number displayed on the indicator refers to your A8 QC’s remaining charge. Please refer to the table below.
Charge Level Indication
When the A8 QC is not being charged, the current charge level is indicated with a steady glow.
When the A8 QC is being charged, the charge level is indicated with a blinking number.
This product includes an 18-month limited warranty, starting on the date of purchase, excluding accessories. Free exchange or repair service is offered to rectify manufacturing defects or other quality issues during the valid warranty period. Please note that the warranty will be void if product has been misused, disassembled, or physically damaged. Warranty service is only available for products purchased through authorized sellers, and proof of purchase is required.
For warranty service, please fill out our Support Form and we will get in touch with you as soon as possible.
Important Information Before Use
Although the Zendure A-Series battery is designed to be extremely durable, and it can be run over by a car in our tests, please do not attempt to stage your own durability trials.
ZEN+ Technology means each port automatically detects your device and fine tunes the output to charge it at maximum speed (up to 3.1A each port, and 3.1A in total among 3 ports). So, if you plug in two devices, each device will get 1.55A (except for a tablet and a phone, when the tablet will get 2.1A, and the phone gets 1A); three devices with 1A each.
Energy Efficiency and Charging Capability
To approximate how many times a Zendure battery can charge your device, multiply the battery's capacity by 0.8, and then divide it by the capacity of your device. This formula assumes that the device's nominal voltage is about 3.7V, is charged at 1A in a 25°C environment, and is powered off and not in use when being charged. Actual results may vary slightly depending on whether the device is in use, output used, temperature, how much heat the device's battery generates, the condition of the device, etc.
The A8 QC is capable of charging your devices when itself is being charged. During charge-through mode, the Quick Charge 3.0 port still works even if you don’t use a Quick Charge 3.0 or 2.0 compatible charger to charge the Zendure, as long as the battery is not completely empty. The output specs for the four ports are the same with that when it’s working standalone.
Some energy will be consumed if there’s a USB connection, so please remember to unplug all USB cables for long-term standby. Please charge the external battery at least once every 6 months.
Zendure does not charge when connected to a power source
Make sure that your Zendure is connected to a compatible powered USB port as outlined in the “Charging your Zendure” section of this manual.
Check that the power source is activated. If connected to a computer, make sure the computer is turned on. If connected to a wall charger, ensure that the power outlet is active.
Your Zendure’s multi-protection system may have been engaged. Please refer to the “Multi-protection system” section of this manual.
Zendure does not charge other devices
Ensure that the device is a 5V powered device, and it draws over 120mA of current.
Zendure’s auto-charge capability may not be compatible with all devices. Press the power button to activate your Zendure.
Ensure that your Zendure is charged. Please refer to the “Charging your Zendure” section of this manual.
Your Zendure’s multi-protection system may have been engaged.
To enhance product safety and reduce the risk of permanent damage, your Zendure is equipped with a protection system that temporarily deactivates the device in a number of circumstances, including product overheating, electrical overload, short circuits and connection to an incompatible device. If your Zendure’s multi-protection system is engaged, please follow these steps to reactivate it:
1. Disconnect all cables and devices from your Zendure.
2. If your Zendure is wet, dry it thoroughly with a cloth. If there is moisture in the USB ports, allow the Zendure to dry thoroughly. Do not place fingers or a foreign object inside your Zendure’s ports to expedite drying.
3. If your Zendure has been exposed to a temperature outside of its specified operating range, return it to an environment suitable for operation, taking care to avoid moisture condensation. Keep your Zendure in a suitable environment for at least one hour before attempting to reset the device.
4. Press the power button to reactivate your Zendure. The status lights should turn on at this time. If the status lights do not turn on, try to charge the Zendure with a wall charger.